Tyg02 kprobe

is that good or bad? i dont know anything about kprobe

That’s… bad.

Quite a spiking effect you have there, too…

i see… now i just converted to 811s with HS0K firmware. what are the best settings for the 411s@811s for TYG02 media? (using omnipatcher). also i heard firmware HS0K is the best, should i go to HS0R?

I have the same question as above, except my media code is TYG01 (dvd-r)


Unique Disc Identifier : [DVD-R:TYG01]

Disc Type : [DVD-R]
Manufacturer ID : [TYG01]
Manufacturer Name : [Taiyo Yuden Co. Ltd.]
Disc Application Code : [Unrestricted Use : Consumer Purpose]
Recording Speeds : [1x , 2x , 4x] (8x Cannot Be Detected)
Blank Disc Capacity : [2,298,496 Sectors = 4,489.3MB = 4.38GB (4.71GB)]

** INFO : Hex Dump Of ‘Media Code’-Block Listed Below
** INFO : 4-Byte Header Preceding ‘Media Code’-Block Discarded
** INFO : Format 0Eh - Pre-Recorded Information In Lead-In
0000 : 01 40 c1 fd 9e d8 52 00 02 86 0d 13 66 78 80 00 .@…R…fx…
0010 : 03 54 59 47 30 31 00 00 04 00 00 00 00 00 00 00 .TYG01…
0020 : 05 88 80 00 00 00 01 00 06 08 0f 11 87 78 80 00 …x…
0030 : 07 88 80 00 00 00 00 00 08 05 16 0d 0f 0b 0b 00 …
0040 : 09 97 08 0f 0b 00 00 00 0a 00 00 00 00 00 10 00 …
0050 : 0b 05 1b 13 a8 89 65 00 0c b6 89 88 80 00 00 00 …e…
0060 : 0d 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 …
0070 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
0080 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
0090 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00a0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00b0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00c0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00d0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00e0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00f0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …

[DVD Identifier - http://DVD.Identifier.CDfreaks.com]

I have seen those spikes like that before when there is dirt on the heads or something…