New Firmware Lg4163b

vbimport

#1

New Firmware Lg4163b on the german-site!


#2

Thank you, matra. Super 1st post! :cool:


#3

Well it loads ok, no change log in zip file or on d/l page.


#4

Only their typical description:

[B]Model:GSA-4163B
Ver:A101
Improvement Point

  • Improvement of DVD recording quality [/B] :confused:

#5

Ok guys, Ritek 16x DVD+R (R04) is now fully supported @ 16x :cool:


#6

Ricoh 16x DVD+R (RICOHJPN R03) also 16x certify :iagree:


#7

new support for 16x media (a lot are not 16x certified for LG)

  • format
    Infodisc R20, BeAll G16001, MBI 03RG40, FUJIFILM04, NSDR40, RITEKG07, MEI 00V003
  • format
    MBIPG101R05, BeAll000PG0, NSD R40, INFOME R03, LGEP16 001, plasmon2C01, Philips C16

#8

Still does NOT remember BT setting after power off!


#9


#10

I took a 2nd look at the code, seems like they didn’t clean up the previous speed… :eek:


A100


A101


#11

08 02 00 00 01 0F 02 00 00 03 00 00 00 26 05 3F …&.?
00 00 00 00 00 00 00 59 55 44 45 4E 30 30 30 54 …YUDEN000T
30 32 00 38 23 54 37 10 02 4E 72 02 8C 63 16 16 02.8#T7…Nr…c…
0B 0B 0A 0A 01 19 1B 0C 0C 0C 0D 01 00 00 00 00 …

First test with YUDEN T02 @12x ( TDK DVD+R 8x )
The 12x part gets ugly but… :wink:


#12

It reach 16x at the 3.5Gb mark. :rolleyes:
Could it reach 17x or 18x speed if it would be CAV al the way up? :confused:

5:36 for 4.38Gb is one of the fastests times I have seen so far. :iagree:


#13

My record is still 5:28min with CMC 16x DVD+R :eek:

My other friend raygay managed 5:25min with TDK 16x DVD-R. (- is alway faster)

5:18min is possible with Maxell 16x DVD-R. Hopefully we can see 18x drives next spring. :o


#14

New Fw A101 YUDEN000-T02-00 12x test
4.2gb data disk burn
nero 6.6.0.3

scanning with PX 716 fw 1.03



#15

just downloaded …thanks!!!


#16

Thx! Here is a scan of Verbatim 16X with A101 Firmware. 6:06 burn time ( 4464Mb )



#17

Found a scan of an MCC004 disc burned at 16x on a 4163B on a Japanese message board site. It has to be the best 16x PIE scan I’ve ever seen.


#18

Hm. Only PIE scanned in PX-716A? My result with MCC004 at 16x showed less than 100 total PIF errors when scanning in SOHW-1613S BS41 firmware at 2x read speed and about 125 at 4x read speed. It’s probably just a matter of time to see 4.7GB completed in less than 5:20 and still shows less than 5,000 PIE’s and 10 PIF’s. :slight_smile:

Anyway, now A101 firmware is out finally. :slight_smile:

(All my GSA-5163D tests were done with A101 firmware.)


#19

It seems there’s no PIF at all except during the 12x zone. TDK YUDEN000T02 must be of the best quality for YUDEN000T02. :slight_smile:


#20

5:36 is rather slow for GSA-4163/5163. :bigsmile: