Nero Freeze

After about one hour of burning an AVI file my Nero just freezes up. I’ve been trying to burn “Almost Famous” for the past 2 days. I pop in my DVD, upload the file and begin the burn. It says the estimated ETA is 2 hours but if you check back in 4 hours it is only 1 hour or so into the burning and frozen at the same spot every time. I’ve watched the file so I know it’s fine, any ideas? I also have to endtask my program so it doesn’t save the log but I’ll post my entire history so you can see if there are any problems, any help would be appreciated.

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 60MB (62052kB)
Memory in use : 92
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

24.5.2006
NeroAPI
9:58:26 PM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

9:58:27 PM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

9:58:27 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

9:58:27 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

9:58:27 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

9:58:27 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

9:58:27 PM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

9:58:27 PM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1837903 (408:25.28, 3589MB)

9:58:27 PM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

9:58:27 PM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

9:58:27 PM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

9:58:27 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1837904 (1837904) = #1837904/408:25.29
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1837904 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

9:58:27 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3764027392, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1837904 | lead-out | 1 | 0x41 | 0x00

9:58:27 PM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

9:58:27 PM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

9:58:27 PM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

9:58:27 PM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

9:58:27 PM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

9:58:27 PM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

9:58:27 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

9:58:28 PM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

9:58:28 PM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

9:58:28 PM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

9:58:56 PM #24 Text 0 File Cdrdrv.cpp, Line 1211
21:58:56.578 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

10:04:58 PM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1837904 (1C0B50h), length 0 blocks

10:04:58 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

10:04:58 PM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1837903

10:05:16 PM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 176MB (180832kB)
Memory in use : 76
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

25.5.2006
NeroAPI
9:26:47 PM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

9:26:47 PM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

9:26:47 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

9:26:47 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

9:26:47 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

9:26:47 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

9:26:47 PM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

9:26:48 PM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1947807 (432:50.57, 3804MB)

9:26:48 PM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

9:26:48 PM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

9:26:48 PM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

9:26:48 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1947808 (1947808) = #1947808/432:50.58
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1947808 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

9:26:48 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3989110784, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1947808 | lead-out | 1 | 0x41 | 0x00

9:26:48 PM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

9:26:48 PM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

9:26:48 PM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

9:26:48 PM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

9:26:48 PM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

9:26:48 PM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

9:26:48 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

9:26:48 PM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

9:26:48 PM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

9:26:48 PM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

9:27:17 PM #24 Text 0 File Cdrdrv.cpp, Line 1211
21:27:17.343 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

9:33:39 PM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1947808 (1DB8A0h), length 0 blocks

9:33:39 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

9:33:39 PM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1947807

9:33:57 PM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
juan
snipe inc.
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero Version: 7.0.8.2
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <Generic DVD-ROM >Version: 1.0 - HA 1 TA 3 - 7.0.8.2
Adapter driver: <SCSI> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 445MB (455916kB)
Memory in use : 41
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

26.5.2006
CueSheet
1:18:02 AM #1 Text 0 File Burncd.cpp, Line 3056
HL-DT-ST DVDRAM GSA-4163B
Buffer underrun protection activated

1:18:02 AM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 81920KB of Memory

1:18:02 AM #3 Text 0 File Reader.cpp, Line 124
Reader running

1:18:02 AM #4 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using CD-R/RW media

1:18:08 AM #5 Phase 40 File dlgbrnst.cpp, Line 1730
Aborted by user

1:18:08 AM #6 Text 0 File DlgWaitCD.cpp, Line 289
Disc check failed: Medium not allowed (Wrong CD)

1:18:08 AM #7 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

1:18:08 AM #8 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B
Medium not present

1:18:08 AM #9 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Compilation cannot be written on that medium type.
(Medium in drive: DVD-R. Medium required by compilation: CD-R/RW.)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)
File ‘Drivers\scsiport.sys’: Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/12/2004 9:04:49 AM (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** Nero Burning ROM, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 171MB (175456kB)
Memory in use : 77
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

26.5.2006
NeroAPI
2:56:20 AM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

2:56:21 AM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

2:56:21 AM #3 Text 0 File Reader.cpp, Line 124
Reader running

2:56:21 AM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

2:56:21 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

2:56:21 AM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

2:56:21 AM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

2:56:22 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1668319 (370:44.19, 3258MB)

2:56:22 AM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

2:56:22 AM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

2:56:22 AM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

2:56:22 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1668320 (1668320) = #1668320/370:44.20
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1668320 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

2:56:22 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3416719360, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1668320 | lead-out | 1 | 0x41 | 0x00

2:56:22 AM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

2:56:22 AM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

2:56:22 AM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

2:56:22 AM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

2:56:22 AM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

2:56:22 AM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

2:56:22 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

2:56:22 AM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

2:56:22 AM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

2:56:22 AM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

2:56:53 AM #24 Text 0 File Cdrdrv.cpp, Line 1211
02:56:53.125 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

3:02:24 AM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1668320 (1974E0h), length 0 blocks

3:02:24 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

3:02:24 AM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1668319

3:02:40 AM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 159MB (162896kB)
Memory in use : 79
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

26.5.2006
NeroAPI
10:50:22 AM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

10:50:23 AM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

10:50:23 AM #3 Text 0 File Reader.cpp, Line 124
Reader running

10:50:23 AM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

10:50:23 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

10:50:23 AM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

10:50:23 AM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

10:50:23 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1982911 (440:38.61, 3872MB)

10:50:23 AM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

10:50:23 AM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

10:50:23 AM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

10:50:23 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1982912 (1982912) = #1982912/440:38.62
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1982912 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

10:50:23 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4061003776, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1982912 | lead-out | 1 | 0x41 | 0x00

10:50:23 AM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

10:50:23 AM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

10:50:23 AM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

10:50:23 AM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

10:50:23 AM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

10:50:23 AM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

10:50:23 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

10:50:23 AM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

10:50:23 AM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

10:50:23 AM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

10:50:53 AM #24 Text 0 File Cdrdrv.cpp, Line 1211
10:50:53.718 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

10:57:22 AM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1982912 (1E41C0h), length 0 blocks

10:57:22 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

10:57:22 AM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1982911

10:57:40 AM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 154MB (158520kB)
Memory in use : 79
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

26.5.2006
NeroAPI
3:20:32 PM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

3:20:32 PM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

3:20:32 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

3:20:32 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

3:20:32 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:20:33 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:20:33 PM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

3:20:33 PM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1816623 (403:41.48, 3548MB)

3:20:33 PM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

3:20:33 PM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

3:20:33 PM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

3:20:33 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1816624 (1816624) = #1816624/403:41.49
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1816624 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

3:20:33 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3720445952, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1816624 | lead-out | 1 | 0x41 | 0x00

3:20:33 PM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

3:20:33 PM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

3:20:33 PM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

3:20:33 PM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

3:20:33 PM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

3:20:33 PM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

3:20:33 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

3:20:33 PM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

3:20:33 PM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

3:20:33 PM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

3:21:03 PM #24 Text 0 File Cdrdrv.cpp, Line 1211
15:21:03.156 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

3:27:01 PM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1816624 (1BB830h), length 0 blocks

3:27:01 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

3:27:01 PM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1816623

3:27:19 PM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 5 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom5
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 206MB (211496kB)
Memory in use : 73
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

27.5.2006
NeroAPI
3:38:21 PM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

3:38:21 PM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

3:38:21 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

3:38:21 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

3:38:22 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:38:22 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:38:22 PM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

3:38:22 PM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2015999 (447:59.74, 3937MB)

3:38:22 PM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

3:38:22 PM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

3:38:22 PM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

3:38:22 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2016000 (2016000) = #2016000/448:0.0
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2016000 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

3:38:22 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4128768000, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2016000 | lead-out | 1 | 0x41 | 0x00

3:38:22 PM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

3:38:22 PM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

3:38:22 PM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

3:38:22 PM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

3:38:22 PM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

3:38:22 PM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

3:38:22 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

3:38:22 PM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

3:38:22 PM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

3:38:22 PM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

3:38:53 PM #24 Text 0 File Cdrdrv.cpp, Line 1211
15:38:53.625 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

3:45:28 PM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 2016000 (1EC300h), length 0 blocks

3:45:28 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

3:45:28 PM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 2015999

3:45:46 PM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 0 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 94MB (96872kB)
Memory in use : 87
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

28.5.2006
NeroAPI
2:27:14 PM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

2:27:19 PM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

2:27:19 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

2:27:19 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

2:27:19 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

2:27:19 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

2:27:19 PM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

2:27:20 PM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1943871 (431:58.21, 3796MB)

2:27:20 PM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

2:27:20 PM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

2:27:20 PM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

2:27:20 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1943872 (1943872) = #1943872/431:58.22
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1943872 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

2:27:20 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3981049856, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1943872 | lead-out | 1 | 0x41 | 0x00

2:27:20 PM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

2:27:20 PM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

2:27:20 PM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

2:27:20 PM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

2:27:20 PM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

2:27:20 PM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

2:27:20 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

2:27:20 PM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

2:27:20 PM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

2:27:20 PM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 00 10 20 00 00 00 - 00 00 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

2:27:51 PM #24 Text 0 File Cdrdrv.cpp, Line 1211
14:27:51.625 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

2:34:13 PM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1943872 (1DA940h), length 0 blocks

2:34:13 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

2:34:13 PM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1943871

2:34:31 PM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 0 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 73MB (75672kB)
Memory in use : 90
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

1.6.2006
NeroAPI
10:45:59 AM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

10:45:59 AM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

10:45:59 AM #3 Text 0 File Reader.cpp, Line 124
Reader running

10:45:59 AM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

10:45:59 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

10:45:59 AM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

10:45:59 AM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

10:46:00 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1859119 (413:08.19, 3631MB)

10:46:00 AM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

10:46:00 AM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: FUJIFI - LM03
Disc Application Code: 64, Disc Physical Code: 193

10:46:00 AM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

10:46:00 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1859120 (1859120) = #1859120/413:8.20
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1859120 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

10:46:00 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3807477760, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1859120 | lead-out | 1 | 0x41 | 0x00

10:46:00 AM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

10:46:00 AM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

10:46:00 AM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

10:46:00 AM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

10:46:00 AM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

10:46:00 AM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

10:46:00 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

10:46:00 AM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

10:46:00 AM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

10:46:00 AM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 01 02 04 06 00 00 - 00 08 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

10:46:29 AM #24 Text 0 File Cdrdrv.cpp, Line 1211
10:46:29.562 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

10:52:35 AM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1859120 (1C5E30h), length 0 blocks

10:52:35 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

10:52:35 AM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1859119

10:52:53 AM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 0 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 81MB (83864kB)
Memory in use : 89
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

2.6.2006
NeroAPI
11:31:41 AM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

11:31:42 AM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

11:31:42 AM #3 Text 0 File Reader.cpp, Line 124
Reader running

11:31:42 AM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

11:31:42 AM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

11:31:42 AM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

11:31:42 AM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

11:31:42 AM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1960479 (435:39.54, 3829MB)

11:31:42 AM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

11:31:42 AM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: FUJIFI - LM03
Disc Application Code: 64, Disc Physical Code: 193

11:31:42 AM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

11:31:42 AM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1960480 (1960480) = #1960480/435:39.55
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1960480 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

11:31:42 AM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4015063040, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1960480 | lead-out | 1 | 0x41 | 0x00

11:31:42 AM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

11:31:42 AM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

11:31:42 AM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

11:31:43 AM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

11:31:43 AM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

11:31:43 AM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

11:31:43 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

11:31:43 AM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

11:31:43 AM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

11:31:43 AM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 01 02 04 06 00 00 - 00 08 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

11:32:11 AM #24 Text 0 File Cdrdrv.cpp, Line 1211
11:32:11.296 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

11:38:36 AM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1960480 (1DEA20h), length 0 blocks

11:38:36 AM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

11:38:36 AM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1960479

11:38:54 AM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======
4C80-0010-8011-0000-2608-4739-1801

Windows XP 5.1
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.71 (0002), size=45056 bytes, created 7/17/2002 10:20:56 AM
ahead WinASPI: File ‘C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll’: Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM

NT-SPTI used
Nero API version: 7.0.8.2
Using interface version: 7.0.0.0
Installed in: C:\Program Files\Nero\Nero 7\Core
Application: ahead\NeroVision
Internal Version: 7, 0, 8, 2

Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A106 - HA 1 TA 0 - 7.0.8.2
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?

=== Scsi-Device-Map ===
CdRomPeripheral : SCSI DVD-ROM 1.0 VClone Port 0 ID 0 DMA: Off
DiskPeripheral : WDC WD400BB-75JHA0 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 2 ID 0 DMA: On
CdRomPeripheral : SAMSUNG CD-R/RW SW-252S atapi Port 2 ID 1 DMA: Off
CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B D: CDRom0
SAMSUNG CD-R/RW SW-252S E: CDRom1
Generic DVD-ROM F: CDRom3
SCSI DVD-ROM H: CDRom2

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 765MB (784368kB)
Free physical memory: 103MB (106000kB)
Memory in use : 86
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

2.6.2006
NeroAPI
3:09:22 PM #1 Phase 111 File APIProgress.cpp, Line 278
DVD-Video files sorted

3:09:22 PM #2 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 262144KB of Memory

3:09:22 PM #3 Text 0 File Reader.cpp, Line 124
Reader running

3:09:22 PM #4 Text 0 File Writer.cpp, Line 113
Writer D: HL-DT-ST DVDRAM GSA-4163B running

3:09:22 PM #5 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:09:22 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:09:23 PM #7 Text 0 File Burncd.cpp, Line 3353
Turn on Disc-At-Once, using DVD media

3:09:23 PM #8 Text 0 File DlgWaitCD.cpp, Line 289
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1696143 (376:55.18, 3312MB)

3:09:23 PM #9 Text 0 File DlgWaitCD.cpp, Line 301
Write in overburning mode: NO (enabled: CD)

3:09:23 PM #10 Text 0 File DlgWaitCD.cpp, Line 2715
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: FUJIFI - LM03
Disc Application Code: 64, Disc Physical Code: 193

3:09:23 PM #11 Text 0 File DlgWaitCD.cpp, Line 473
>>> Protocol of DlgWaitCD activities: <<<
=========================================

3:09:23 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1696144 (1696144) = #1696144/376:55.19
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1696144 blocks [D: HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

3:09:23 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [D: HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3473702912, ISRC “”
DAO layout:
===========
Start|Track|Idx|CtrlAdr|RecDep_____
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1696144 | lead-out | 1 | 0x41 | 0x00

3:09:23 PM #14 Text 0 File SCSIPassThrough.cpp, Line 39
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

3:09:23 PM #15 Text 0 File SCSIPassThrough.cpp, Line 84
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

3:09:23 PM #16 Phase 24 File APIProgress.cpp, Line 278
Caching of files started

3:09:23 PM #17 Text 0 File Burncd.cpp, Line 4187
Cache writing successful.

3:09:23 PM #18 Phase 25 File APIProgress.cpp, Line 278
Caching of files completed

3:09:23 PM #19 Phase 36 File APIProgress.cpp, Line 278
Burn process started at 8x (11,080 KB/s)

3:09:23 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2707
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

3:09:23 PM #21 Text 0 File DVDR.cpp, Line 2760
Recording mode: Sequential Recording Mode

3:09:23 PM #22 Text 0 File DVDR.cpp, Line 2916
Start write address at LBA 0
DVD high compatibility mode: Yes

3:09:23 PM #23 Text 0 File Cdrdrv.cpp, Line 8661
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 30 01 02 04 06 00 00 - 00 08 00 00 00 00 00 00 .0…
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …þ…ÿ…
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

3:10:09 PM #24 Text 0 File Cdrdrv.cpp, Line 1211
15:10:09.265 - D: HL-DT-ST DVDRAM GSA-4163B : Queue again later

3:15:45 PM #25 Text 0 File WriterStatus.cpp, Line 116
<D: HL-DT-ST DVDRAM GSA-4163B> start writing Lead-Out at LBA 1696144 (19E190h), length 0 blocks

3:15:45 PM #26 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

3:15:45 PM #27 Text 0 File DVDR.cpp, Line 3156
EndDAO: Last written address was 1696143

3:16:01 PM #28 Phase 37 File APIProgress.cpp, Line 278
Burn process completed successfully at 8x (11,080 KB/s)

Existing drivers:
File ‘Drivers\ADPU160M.SYS’: Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/12/2004 8:55:45 AM
File ‘Drivers\ASPI32.SYS’: Ver=4.71 (0002), size=16877 bytes, created 7/17/2002 9:53:02 AM
File ‘Drivers\PXHELP20.SYS’: Ver=2.03.16a, size=20576 bytes, created 8/2/2004 3:03:00 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

====== *** NeroAPI, History File *** ======

Probably a good idea to upgrade Nero to 7.2.0.3 as earlier versions at quite buggy.

also, when posting nero logs be sure to put them within CODE tags so they don’t take up 8 million screens.

I’m not sure if this is related to your problem, but it looks like you have some DMA issues. double check in the device manager and make sure DMA is enabled on all of your drives.