Nero 5.5.10.56 driving me nuts

vbimport

#1

I hope this is the correct place to post this.

I’m running Windows 98 SE on a Pentium III and using Nero. It’s been working fine forever. However, recently, the registry messed up and Windows restored a previous one. Since then, I can’t burn cdr disks. I’ve uninstalled and re-installed half a dozen times. I’ve done a complete cleanup as suggested by Nero support. Same result.

What’s strange is that if I burn the compilation to a cr-rw, it works fine but if I try to burn to a cdr, I get an error.

Below is a copy of the error I get after the burn attempt stops:

=====================================================================

Windows 98 4.10
IA32
WinAspi: File ‘Wnaspi32.dll’: Ver=4.60 (1021), size=45056 bytes, created 05/06/2003 6:21:26 PM
Nero Version: 5.5.10.56
Recorder: < CD-R/RW RW7060A> Version: 1.80 - HA 0 TA 0 - 5.5.10.56
Adapter driver: <ESDI_506> HA 0
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: < CD-R/RW RW7060A>Version: 1.80 - HA 0 TA 0 - 5.5.10.56
Adapter driver: <ESDI_506> HA 0
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-R/RW RW7060A (Target 0, D:): Autoinsert Off, DMA On, Disconnect On, SyncDataXfer Off
Excluded drive IDs:
CmdQueuing : 1
CmdNotification: 2
WriteBufferSize: 24117248 (0) Byte
ShowDrvBufStat : 0
EraseSpeed : 0
BUFE : 0
Physical memory : 127MB (130460kB)
Free physical memory: 0MB (384kB)
Memory in use : 82 %
Uncached PFiles: 0x0
Use Static Write Speed Table: 0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Enabled (1)
Wizard: On

24.6.2005
CD-ROM (ISO)
6:03:43 PM #1 Text 0 File Isodoc.cpp, Line 7604
Iso document burn settings

Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

6:03:43 PM #2 Text 0 File Reader.cpp, Line 115
Reader running

6:03:43 PM #3 Text 0 File Writer.cpp, Line 125
Writer CD-R/RW RW7060A running

6:03:43 PM #4 ISO9660GEN -11 File geniso.cpp, Line 4571
First writeable address = 0 (0x00000000)

6:03:43 PM #5 Text 0 File Burncd.cpp, Line 3773
Turn on Track-At-Once, using CD-R/RW media

6:03:43 PM #6 Text 0 File ThreadedTransferInterface.cpp, Line 672
Setup items (original item values)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original CD pos #0 + 200626 (200626) = #200626/44:35.1
relocatable, CD pos for caching/writing not required/required, no patch infos

6:03:57 PM #7 Text 0 File DlgWaitCD.cpp, Line 229
Last possible write address on media: 359845 (79:59.70)
Last address to be written: 200625 (44:37.00)

6:03:57 PM #8 Text 0 File DlgWaitCD.cpp, Line 234
Write in overburning mode: FALSE

6:03:57 PM #9 Text 0 File DlgWaitCD.cpp, Line 1703
Recorder: CD-R/RW RW7060A;
CDR code: 00 97 26 66; OSJ entry from: CMC Magnetics Corporation
ATIP Data:
Special Info [hex] 1: D0 00 98, 2: 61 1A 42 (LI 97:26.66), 3: 4F 3B 47 (LO 79:59.71)
Additional Info [hex] 1: 00 00 80 (invalid), 2: 00 00 00 (invalid), 3: 00 00 00 (invalid)

6:03:57 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 824
Prepare recorder CD-R/RW RW7060A for write in TAO
DAO infos:

MCN:
TOCTYPE: 0x0 Session Closed, CD not fixated
Tracks 1 to 1:
TRM_DATA_MODE1, 2048/0x0, ISRC “”, FilePos 0 307200 411189248

6:03:57 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 852
Removed 2 run-out blocks from end of track 1.

6:03:57 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 672
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (CTransferItem)
2 indices, index0 (150) not provided
original CD pos #0 + 200626 (200626) = #200626/44:35.1
relocatable, CD pos for caching/writing not required/required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 200624 blocks [ CD-R/RW RW7060A ]

6:03:57 PM #13 Phase 24 File dlgbrnst.cpp, Line 1655
Caching of files started

6:04:00 PM #14 Phase 25 File dlgbrnst.cpp, Line 1655
Caching of files completed

6:04:00 PM #15 Phase 36 File dlgbrnst.cpp, Line 1655
Burn process started at 6x (900 KB/s)

6:04:00 PM #16 Text 0 File ThreadedTransferInterface.cpp, Line 1978
Verifying CD position of item 0 (relocatable, CD pos, no patch infos, orig at #0): write at #0

6:04:10 PM #17 SCSI -1152 File Cdrdrv.cpp, Line 1447
SCSI Exec, HA 0, TA 0, LUN 0, buffer 0x02670000
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x64
Sense Qual: 0xC0
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x1F 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0C
0x00 0x00 0x00 0x00 0x64 0xC0

6:04:10 PM #18 MMC -1152 File Writer.cpp, Line 333
Medium speed error

6:04:10 PM #19 Text 0 File ThreadedTransfer.cpp, Line 222
all writers idle, stopping conversion

6:04:10 PM #20 Text 0 File ThreadedTransfer.cpp, Line 216
conversion idle, stopping reader

6:04:10 PM #21 CDR -201 File WriterStatus.cpp, Line 194
Invalid write state

6:04:10 PM #22 TRANSFER -18 File WriterStatus.cpp, Line 194
Could not perform EndTrack

6:04:10 PM #23 Text 0 File Mmc.cpp, Line 14537
< CD-R/RW RW7060A > start Close Session

6:04:10 PM #24 SCSI -1176 File Cdrdrv.cpp, Line 1243
SCSI Exec, HA 0, TA 0, LUN 0
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x72
Sense Qual: 0x04
CDB Data: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x71 0x00 0x05 0x00 0x00 0x00 0x00 0x0C
0x00 0x00 0x00 0x00 0x72 0x04

6:04:10 PM #25 MMC -1176 File WriterStatus.cpp, Line 233
Session fixation error

6:04:10 PM #26 TRANSFER -19 File WriterStatus.cpp, Line 233
Could not perform Fixation

6:04:10 PM #27 Text 0 File WriterStatus.cpp, Line 242
falling back to disc fixation

6:04:10 PM #28 Text 0 File Mmc.cpp, Line 14537
< CD-R/RW RW7060A > start Close Session

6:04:10 PM #29 SCSI -1176 File Cdrdrv.cpp, Line 1243
SCSI Exec, HA 0, TA 0, LUN 0
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x72
Sense Qual: 0x04
CDB Data: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x71 0x00 0x05 0x00 0x00 0x00 0x00 0x0C
0x00 0x00 0x00 0x00 0x72 0x04

6:04:10 PM #30 MMC -1176 File WriterStatus.cpp, Line 233
Session fixation error

6:04:10 PM #31 TRANSFER -19 File WriterStatus.cpp, Line 233
Could not perform Fixation

6:04:10 PM #32 Phase 38 File dlgbrnst.cpp, Line 1655
Burn process failed at 6x (900 KB/s)

6:04:10 PM #33 Text 0 File Scsicmd.cpp, Line 406
SCSI not using temporary buffers
20 out of 20 temporary buffers allocated

Existing drivers:
File ‘IoSubSys\SCSI1HLP.VXD’: Ver=4.10.1998, size=19270 bytes, created 04/23/1999 10:22:00 PM
File ‘IoSubsys\NEROCD95.VXD’: Ver=4.5.0.14, size=39882 bytes, created 03/11/2002 11:55:38 AM
File ‘IoSubsys\CDFS.VXD’: Ver=4.10.1998, size=59133 bytes, created 04/23/1999 10:22:00 PM
File ‘IoSubsys\ESDI_506.PDR’: Ver=4.10.2222, size=24406 bytes, created 04/23/1999 10:22:00 PM
File ‘…\System\Vmm32\Ios.vxd’: Ver=4.10.2222, size=69570 bytes, created 04/23/1999 10:22:00 PM
File ‘IoSubsys\Disktsd.vxd’: Ver=4.10.2222, size=18809 bytes, created 04/23/1999 10:22:00 PM
File ‘IoSubsys\ESDI_506.PDR’: Ver=4.10.2222, size=24406 bytes, created 04/23/1999 10:22:00 PM (Adapter driver for rec)

Registry Keys:

====================================================================

What I also can’t understand is why it won’t keep the settings I enter when the tabbed screen comes up. If anyone can help me I would apreciate it immensley.