MediaCodeSpeedEdit tool for DVD-Writers

vbimport

#1244

Any chance that the new official TS-U633F v SC00 firmware update could be included in the next version of MCSE?

The other question is DELL OEM TS-U633F D500 firmware supported in MCSE? I checked the changelog and couldn’t find it however I was told it could be patched.

Thanks


#1245

[QUOTE=artecon;2561625]Any chance that the new official TS-U633F v SC00 firmware update could be included in the next version of MCSE?

The other question is DELL OEM TS-U633F D500 firmware supported in MCSE? I checked the changelog and couldn’t find it however I was told it could be patched.[/QUOTE]
The Dell version is already supported, the Samsung version appeared later and is supported in the next release.


#1246

[QUOTE=Nator;2549682]I have two LG drives.
WH08LS20 (aka BH08LS20, Bluray writer) and GH22NS50 (DVD writer with RAM ability).

Downloaded both the wh08ls20 and bh08ls20 firmware files. Both are .exe’s and when I try to load it into MCSE, it fills in the firmware and bootcode info just fine, but the select drive ID is filled with ?'s and there is nothing in the list of types.
[/QUOTE]
This is ok, the ‘?’ are wildcards, matching any drive id.

[I]Edit1:
Also, when loading a file, I get the message that the code list is not yet available for the LG firmware. I see the RPC2 Auto Reset box but not the Riplock box. When loading the GH22NS50 file, there is no drive selection box on the bottom right.[/I]

The read speed increase patch is available for the GH22NS50 TN01/02/03 firmwares. Which firmware did you try ?
There is no crossflash drive id selection box because no crossflash is supported as there is no drive that could be crossflashed.

[I]Edit2:
Okay the issue with the GH22NS50 is that the firmware I’m grabbing isn’t a supported version. However, still having the problem with the firmware file for BH08LS20 v2.00 file.[/I]

Also, please tell me if I’m understanding this correctly. Basically, importing the file, making any changes, exporting it, then using the modified firmware to flash the drive, so that I can burn media at a rate faster than the media was originally designed for (but have it still work just fine anyway). Is that correct?

Basic useage is Load, Change, Save, Flash saved patcheed firmware.
When no media list is displayed, you can not change the media list to increase the write speed.
When the checkboxes for RPC or read speed patches are active, these patches are available, no matter if a media list is displayed nor not displayed.


#1247

Is there also any chance that Samsung SE-S084D would be supported by MCSE?
thanks!


#1248

[QUOTE=Spoks;2565844]Is there also any chance that Samsung SE-S084D would be supported by MCSE?
thanks![/QUOTE]
The media table is packed somehow and the stock RPC1 patch does not find the code to be patched, so this drive is not supported in the next release.


#1249

MediaCodeSpeedEdit V1.2.0.9 is out.

Changelog

1.2.0.9 27 Dec 2010
        - added support for PIONEER DVR-219L 1.01 (QSI DDW-242S clone)
        - added support for PIONEER DVD-RW DVR-217L 1.09 (S17J)
        - added support for PIONEER DVD-RW DVR-K16M 1.10
        - added support for PIONEER DVD-RW DVRTD08A 1.54
        - added support for PIONEER DVD-RW DVRTD08L 2.54
        - added support for PIONEER DVD-RW DVRTD08RS 1.06
        - added support for LG BH10LS30 1.00-09
        - added support for LG BH10NS30 1.00-09
        - added support for LG WH10LS30 1.00-A9
        - added support for LG GU10N MX05-01
        - added support for TSSTcorpCDDVDW TS-U633F SC00

Download Changelog


#1250

[QUOTE=ala42;2565848]The media table is packed somehow and the stock RPC1 patch does not find the code to be patched, so this drive is not supported in the next release.[/QUOTE]

Does anybody have any idea how to make this drive RPC1 ?
:bow:


#1251

Thanks ala42. Your work is greatly appreciated by at least one person down here in Tasmania. :wink:


#1252

Oops, I bought a Lite-on iHBS112, and now I see that it is supported as read only. Does that mean I’m out of luck? The read speeds are horrible with this drive.

Thanks for the effort you’ve made with this program.


#1253

Hmmm, nevermind. My latest read test actually came out ok, and now Anydvd is reading at around 17 MB/s. I’m not sure what changed to make it run that way. Either way, I’m happy.


#1254

Hi everyone,
Just joined the site to see if I could get some help. Usually you guys are great enough that I never have to post. After searching, I came up with nothing for removing riplock from a TS-L633C with current firmware DW50. It is in a Dell laptop. I used MCSE after downloading the firmware and was able to select “RPC1 patch” option. After saving and flashing, the drive still only reads video dvds @ 2~3 MB/sec. Is there support for this drive or will there be? Can I flash with different firmware? Scared to brick the drive so I haven’t done much experimenting. Thanks for all your help.


#1255

Samsung drives have no riplock. Post a cdspeed transfer rate test graph.


#1256

[QUOTE=ala42;2569529]Samsung drives have no riplock. Post a cdspeed transfer rate test graph.[/QUOTE]


#1257

speed set to 4x??


#1258

[QUOTE=chef;2569585]speed set to 4x??[/QUOTE]

That is the highest it can be set with a video dvd. Other dvds allow up to 8x.


#1259

Hello, I want to add 1x and 2x writing speed to a disk, but all checkbox are grayed so I have generated the media code of the disk with DVD indentifier:


Unique Disc Identifier : [DVD+R:MCC-004-000]

Disc & Book Type : [DVD+R] - [DVD-ROM]
Manufacturer Name : [Mitsubishi Chemical Corp.]
Manufacturer ID : [MCC]
Media Type ID : [004]
Product Revision : [Not Specified]
Blank Disc Capacity : [2,295,104 Sectors = 4.70 GB (4.38 GiB)]
Recording Speeds : [1x-2.4x , 4x , 6x-8x , 6x-16x]

** INFO : Hex Dump Of ‘Media Code’-Block Listed Below
** INFO : 4-Byte Header Preceding ‘Media Code’-Block Discarded
** INFO : Format 11h (Method 1) - ADIP Information
0000 : a1 0f 02 00 00 03 00 00 00 26 05 3f 00 00 00 00 …&.?..
0010 : 00 00 07 4d 43 43 00 00 00 00 00 30 30 34 00 38 …MCC…004.8
0020 : 23 54 37 11 02 3c 6e 02 84 68 15 15 0b 0b 08 08 #T7…<n…h…>
0030 : 01 19 1b 0c 0c 0c 0d 01 00 00 00 00 00 00 00 00 …
0040 : 01 00 38 38 02 25 61 1a 05 2e 23 10 04 1e 1d 01 …88.%a…#…
0050 : 00 00 02 25 61 1a 05 2e 23 10 04 1e 1d 01 00 00 …%a…#…
0060 : 02 00 54 70 02 44 61 3c 24 14 0c 0c 01 20 00 00 …Tp.Da<$… …
0070 : 00 00 02 5d 62 42 24 14 0c 0c 01 20 00 00 00 35 …]bB$… …5
0080 : 03 00 54 df 02 44 61 3c 24 14 0c 0c 01 20 00 00 …T…Da<$… …
0090 : 00 00 02 bc 66 58 24 14 0c 0c 01 20 00 00 00 9e …fX$… …
00a0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00b0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00c0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00d0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00e0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …
00f0 : 00 00 00 00 00 00 00 00 …

[ DVD Identifier V5.2.0 - http://DVD.Identifier.CDfreaks.com ]

<n…h… 0030="" 19="" 1b="" 0d="" …="" 0040="" 38="" …88.%a…#…="" 0050="" 25="" 1a="" 05="" 2e="" 23="" 10="" 04="" 1e="" 1d="" …%a…#…="" 0060="" :="" 54="" 70="" 02="" 44="" 61="" 3c="" 24="" 14="" 0c="" 01="" 20="" 00="" …tp.da="">In Media Code Speed Edit, I’ve got 4x, 6x, 8x, 12x, 16x, 18x and 20x enabled for my DVD+R MCC 004 and my question is which byte in the DVD Identifier Media Code corresponds to these writing speed settings so I can change it manually?

I hope you’ve understand my problem. Thanks.</n…h…></n…h…>


#1260

[QUOTE=BaptX;2579685]Hello, I want to add 1x and 2x writing speed to a disk, but all checkbox are grayed so I have generated the media code of the disk with DVD indentifier:


Unique Disc Identifier : [DVD+R:[B]MCC-004[/B]-000]
--------------------------------------------------------------------------[/QUOTE]

I say thats useless because 1x and 2x are out of any specification for DVD+R writing!
The slowest speed is 2.4x and it is very unlikely that there is even a useful necessary reason for 1x and 2x writespeeds…


#1261

Thanks for your answer, I want to add 1x/2x writing speed because some ps2 iso backup doesn’t work when I burn with 4x so I want to try with a slower speed, it probably change nothing but I want to try.
You say the slowest speed is 2.4x but if it can be done at 2.4x it should work at 2x or 1x, no?
So, to answer my question: which byte in the DVD Identifier Media Code corresponds to these writing speed settings so I can change it manually? Thanks.


#1262

I tried to apply the rpc1 patch on my asus 1814blt firmware with MCE.
I downloaded the 1.4 firmware, I uncompressed with upx, I patched the firmware, then I flashed the drive (without recompressed).

The drive appear as rpc1 in windows but, when I play video DVD intro sequence doesn’t appear (only sound), then the movie is jerky with lots of square artefacts.

(When I reflashed with original firmware all is OK.)

Any Idea ?:doh:


#1263

An RPC1 drive is not region free. You have to install a software like DVD Region Killer to handle the region settings.