LG GSA - E10L DVD Burning Continuous Error

vbimport

#1

Had this external burner for around a week now its been working fine, burnt around 20 DVD’s with it perfect every time, no coasters. Yesterday however i was burning anouther DVD and i got an error around 50%, so i tryed again, got the same error again, now after 4 or 5 coasters iv ran about 10-15 simulations using different media, different files, different software, and even on 2 different computers and still get the exact same error at around the 50-70% mark whenever burning to DVD media. However the drive will still burn to CD with no problems.

The following is a LOG file of the last failed simulation:

[B]
NT-SPTI used
Nero Version: 7.5.9.0
Internal Version: 7, 5, 9, 0
(Nero Express)
Recorder: <HL-DT-ST DVDRAM GSA-E10L>Version: LE06 - HA 1 TA 4 - 7.5.9.0
Adapter driver: <USB 2.0> HA 1
Drive buffer : 2048kB
Bus Type : set to ATAPI (3) -> ATAPI, detected: ?
CD-ROM: <CT3558S WNW886V >Version: 1.0 - HA 1 TA 1 - 7.5.9.0
Adapter driver: <SCSI> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : SONY DVD RW DW-Q520A atapi Port 1 ID 0 DMA: On
DiskPeripheral : VIA SATA RAID 0 viamraid Port 2 ID 0 DMA: Off
CdRomPeripheral : CT3558S WNW886V 1.0 aaer6h6d Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
SONY DVD RW DW-Q520A D: CDRom0
CT3558S WNW886V E: CDRom1
HL-DT-ST DVDRAM GSA-E10L F: CDRom4

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
BUFE : 0
Physical memory : 2046MB (2095644kB)
Free physical memory: 1381MB (1414264kB)
Memory in use : 32 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

23.1.2007
Burn DVD Image
7:45:14 PM #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

7:45:15 PM #2 Text 0 File Burncd.cpp, Line 3451
Turn on Disc-At-Once, using DVD media

7:45:15 PM #3 Text 0 File DlgWaitCD.cpp, Line 306
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 1971381 (438:05.06, 3850MB)

7:45:15 PM #4 Text 0 File DlgWaitCD.cpp, Line 318
Write in overburning mode: NO (enabled: CD)

7:45:15 PM #5 Text 0 File DlgWaitCD.cpp, Line 2903
Recorder: HL-DT-ST DVDRAM GSA-E10L, Media type: DVD-R
Disc Manufacturer: MCC 02 - RG20
Disc Application Code: 64, Disc Physical Code: 193

7:45:15 PM #6 Text 0 File DlgWaitCD.cpp, Line 490
>>> Protocol of DlgWaitCD activities: <<<
=========================================

7:45:15 PM #7 Text 0 File ThreadedTransferInterface.cpp, Line 821
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, ISO 9660)
2 indices, index0 (150) not provided
original disc pos #0 + 1971382 (1971382) = #1971382/438:5.7
not relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1971232 blocks [F: HL-DT-ST DVDRAM GSA-E10L]
--------------------------------------------------------------

7:45:15 PM #8 Text 0 File ThreadedTransferInterface.cpp, Line 1024
Prepare [F: HL-DT-ST DVDRAM GSA-E10L] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: “”
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4037390336, ISRC “”
DAO layout:
===========
__Start|___Track|Idx|CtrlAdr|Size|NWA|RecDep
0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 0 | 0x41 | 1971382 | 1971232 | 0x00
0 | 1 | 1 | 0x41 | 1971382 | 1971232 | 0x00
1971382 | lead-out | 1 | 0x41 | 0 | 0 | 0x00

7:45:15 PM #9 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

7:45:15 PM #10 Phase 24 File dlgbrnst.cpp, Line 1746
Caching of files started

7:45:15 PM #11 Text 0 File Burncd.cpp, Line 4278
Cache writing successful.

7:45:15 PM #12 Phase 25 File dlgbrnst.cpp, Line 1746
Caching of files completed

7:45:15 PM #13 Phase 32 File dlgbrnst.cpp, Line 1746
Simulation started at 4x (5,540 KB/s)

7:45:15 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2743
Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0

7:45:15 PM #15 Text 0 File DVDR.cpp, Line 3058
Recording mode: Sequential Recording Mode

7:45:15 PM #16 Text 0 File DVDR.cpp, Line 3214
Start write address at LBA 0
DVD high compatibility mode: Yes

7:45:15 PM #17 Text 0 File Cdrdrv.cpp, Line 9234
---- DVD Structure: Physical Format Information (00h) ----
Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16…63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 …
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 …

7:45:16 PM #18 Text 0 File Cdrdrv.cpp, Line 1292
19:45:16.718 - F: HL-DT-ST DVDRAM GSA-E10L : Queue again later

7:52:44 PM #19 SPTI -1039 File SCSIPassThrough.cpp, Line 179
CdRom4: SCSIStatus(x02) WinError(0) NeroError(-1039)
Sense Key: 0x04 (KEY_HARDWARE_ERROR)
Sense Code: 0x09
Sense Qual: 0x01
CDB Data: 0x2A 00 00 11 8D C0 00 00 20 00 00 00
Sense Area: 0x70 00 04 00 00 00 00 10 32 34 04 0C 09 01
Buffer x083929c0: Len x10000
0xAA 55 BE 74 A0 0E B3 57 FA 3A 58 CE 27 CF B2 7F
0x2F D2 DA 3B C7 63 0D 3C F9 5B B1 C9 CF 50 68 F1
0x0B A8 BC E7 98 CA 8B FF A6 CC 17 CF 4D 12 2A 8A

7:52:44 PM #20 CDR -1039 File Writer.cpp, Line 299
Focus or tracking error
F: HL-DT-ST DVDRAM GSA-E10L

7:52:44 PM #21 Text 0 File DVDR.cpp, Line 3434
EndDAO: Last written address was 1150399

7:52:44 PM #22 CDR -1039 File WriterStatus.cpp, Line 162
Focus or tracking error
F: HL-DT-ST DVDRAM GSA-E10L

7:52:44 PM #23 TRANSFER -24 File WriterStatus.cpp, Line 162
Could not perform end of Disc-at-once

7:52:45 PM #24 Phase 34 File dlgbrnst.cpp, Line 1746
Simulation failed at 4x (5,540 KB/s)

7:52:45 PM #25 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

7:52:49 PM #26 Text 0 File Cdrdrv.cpp, Line 10467
DriveLocker: UnLockVolume completed

7:52:50 PM #27 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

Existing drivers:
File ‘Drivers\PXHELP20.SYS’: Ver=3.00.40a, size=36528 bytes, created 7/24/2006 3:00:00 AM (Prassi/Veritas driver for win 2K)
File ‘Drivers\scsiport.sys’: Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 8/4/2004 12:00:00 PM (Adapter driver for src)[/B]


anyhelp on resolving this issue will be grately appreciated


#2

Try some other media. MCC 02RG20 is good media, but it could be that some of your discs are faulty.
Try burning them at 8x or 16x. :slight_smile: