Conversion not working

vbimport

#1

Conversions do not seem to work. The following is in the log, which is better than flv, as that just dies without any error.

------ begin mobile work(1/1) ------

1m 23.06s: create config(0)
1m 23.06s: convert profile(generic.avi.h264.audiocopy)
1m 25.07s: dvd title(1) angle(0) chapter(1->1)
1m 25.07s: stream(480,2,1) stream(160,65537,0)
1m 26.15s: h264_encode: encode param profile(1) level(30) bitrate(1381)
1m 29.21s: ------ mobile work failed(502.12 7) ------
2m 40.03s:

------ begin mobile work(1/1) ------

2m 40.03s: create config(0)
2m 40.03s: convert profile(generic.avi.divx.audiocopy)
2m 41.67s: dvd title(1) angle(0) chapter(1->1)
2m 41.67s: stream(480,2,1) stream(160,65537,0)
2m 44.75s: ------ mobile work failed(502.12 7) ------


#2

[QUOTE=fischershaw;2541954]Conversions do not seem to work. The following is in the log, which is better than flv, as that just dies without any error.

------ begin mobile work(1/1) ------

1m 23.06s: create config(0)
1m 23.06s: convert profile(generic.avi.h264.audiocopy)
1m 25.07s: dvd title(1) angle(0) chapter(1->1)
1m 25.07s: stream(480,2,1) stream(160,65537,0)
1m 26.15s: h264_encode: encode param profile(1) level(30) bitrate(1381)
1m 29.21s: ------ mobile work failed(502.12 7) ------
2m 40.03s:

------ begin mobile work(1/1) ------

2m 40.03s: create config(0)
2m 40.03s: convert profile(generic.avi.divx.audiocopy)
2m 41.67s: dvd title(1) angle(0) chapter(1->1)
2m 41.67s: stream(480,2,1) stream(160,65537,0)
2m 44.75s: ------ mobile work failed(502.12 7) ------[/QUOTE]

Could you post internal logs? as it seems you need to change the A/V Codec to software but those logs should tell


#3

That text was from dvdfab_internal.log. Are you referring to some other log file?
All codecs are using s/w as reported on the A/V Codecs page.

DVDFab 8.0.0.5 (2010/09/02 13:02:50)
0m 00.79s: option dvd2dvd 1 dvd2mobile 1 bluray2bluray 1 bd2mobile 1 file2mobile 1 filemover 1
1m 02.28s: detected dvd
1m 02.34s: drive D
1m 02.34s: dvd type 1
1m 02.34s: volume label DVDVOLUME
1m 02.68s: got copyright 0 0
1m 03.04s: got udf/iso
1m 03.98s: got discinfo
1m 03.98s: pathplayer enabled
1m 05.65s: got dvdinfo
3m 00.10s:

------ begin mobile work(1/1) ------

3m 00.10s: create config(0)
3m 00.12s: convert profile(generic.avi.h264.audiocopy)
3m 02.14s: dvd title(1) angle(0) chapter(1->1)
3m 02.14s: stream(480,2,1) stream(160,65537,0)
3m 07.54s: h264_encode: encode param profile(1) level(30) bitrate(1381)
3m 10.57s: ------ mobile work failed(502.12 7) ------


#4

Still happens on 8.0.0.9 as well. I tried it on a different machine, same problem for ALL conversions under the Generic ripper list.


#5

[QUOTE=fischershaw;2543259]Still happens on 8.0.0.9 as well. I tried it on a different machine, same problem for ALL conversions under the Generic ripper list.[/QUOTE]

Are you doing the conversion from the hard drive or straight from Disc ?

also are you doing one pass or two ?


#6

I have tried both directly from CD and from a ripped ISO. I also tried both single and 2-pass. I will go through each in a more orderly fashion.


#7

I installed 8.0.1.5 and tried again. The common thread is audiocopy. Using the default settings, any converter which specifies audiocopy rather than mp3 or aac fails immediately. The audio.copy converter under the Audio section does not fail however. Input audio is PCM/2.


#8

Is any additional information needed?