LiteOn 165H6S Test Firmware Results

OS,HT on
Fujifilm 16x dvd+r at 16x

a coaster?

OS,HT on

Philips 16x dvd-r at 16x

HT/OS on

Sony 8x DVD-R at 12x

Ok here is an old one in case it still of interest, a CD.
TDK 32x burnt @32x

For those of you experienced with CD what are criterias regarding C1/C2. From what I got from a 2003 thread no C2, c1 average of less than 0.5 and a max of less than 20 is good.
thks

rgds, soso

---

Last edited by sosotiit; 29-03-2006 at 06:38.

Yuden TYG01 4x at 8x

OS/HT on

YUDEN TYG03 16x dvd-r at 16x

os/ht on

New batch of MKM_A02 +RW 4X (branded verbatim)
1) MKM_A02 at 4X, not good
2) MKM_A02 at 2.4X on another disc and not better
returned the batch and bought Sony +RW 4x (SONY_S11)
3) SONY_S11 at 4X, much better
rgds, Soso

OPTODISCW002 at 2x (maxell dvd-RW 2x) graph 1 & 2
and
MCC003 at 12x (Verbatim DVD+R lightscribe) graph 3
rgds, soso

HV7U needs a bit more work it seems. My burner stops burning when using creat data disc part way into the burn at times.

Can you show some scans you've made from the drive? What media did you use to cause your burner to stop working?

I could not scan these dics. they were TY02 from Sony and Verbatim 16x dash- media.

Have you tried to test burn more? It typically takes at least the 3rd test burn to get a start.

MCC02RG20 HV7U 8x@12x PCAV H/T & O/S on.

Two different Sony YUDEN T02@8X burned same image with CD-DVD Speed
First scan HT off, OS off on first disc
Rest of scans HT on, OS on of second disc scanned with 165H6S@8X, BenQ 1650@8X P-CAV, BenQ 1650@6X CLV

Another burn falure with HV7U and DVD CD Speed 4.50. Create data disc with mcc03rg20 burn at 8x speed stop at 2018 mb. Had to hard reboot to get CD speed to open again after burn failure. Problem is intemittent.

MCC 003@ 12x. HT, OS, SB, all on.
Scan from the 1635 of this disc.

Definitely not ready to burn DL discs.
Verbatim MKM 001
HT/OS on
Burned with CloneCD 5.281@6X
F/W HV7U

---

Last edited by scarfaceal; 05-04-2006 at 08:47.

Slightly out of subject but just tought I would share. Same burn scanned at 4X and then scanned at 8X just to compare the impact of scanning speed!!!
Tried also at 2x with results almost similar to 4X.
Not sure 8x scanning is that good at this point, at least not with my drive on this media.
rgds, Soso

Hi,

RITEKR03 @8x HT/OS = ON

RitekRo3 @8X
HT on / OS OFF / Smart Burn Off

Just to comparing .... HT /OS OFF SB ON

Bad Scans yet ...

HT/OS/SB all ON burned @8x

Changed the media now to DVD-R MCC2RG20

PIF and PI decreased, with this could I conclude that my RitekR03's +R are crap ?

Not necessarily, It seems to be an issue with other 6S Lite-ON drives aswell, as Appie72 in the LiteOn 165P6S Test Firmware Results thread is having similar problems.

http://club.cdfreaks.com/showthread.php?t=172012&page=6

I've been burning some CMC MAG AE1 and having poor results in both my 165h6s and 165p6s. I've burned 5 in each so far, attached are a summary and kprobes of the bad discs.

Hi,

Now RitekR03 with HT/SB/OS ON, burned now @12X, I think that I had some quality improvement !!!

What do you think ?